Experiencing the Netgear extender red light issue can stop one from making the most of their Netgear wireless range extenders. Are you also not able to make the most of your networking device because of the same issue despite performing Netgear extender setup via mywifiext.net successfully? Well then, thankfully, you have come to the right article. Here, we have talked about how you can convert the blinking red LED on your device to green. Thus, keep reading.
[Fixed] Netgear Extender Red Light Issue
- Restart the Netgear Extender
Restarting the Netgear wireless range extender is the very first thing that users prefer doing whenever they get stuck with technical issues. And unfortunately, this hack has helped most of them. Taking this into consideration, you should also try to restart your networking device. For that, you need to power off your extender, remove it from its socket, wait for some time, and reverse the first two steps. Once you have restarted your Netgear extender, check if the red light issue has been troubleshot. On the off chance, you are still experiencing it; you should take a walk through the below-mentioned troubleshooting hacks.
- Change the Connection Source
Another reason why you are experiencing the Netgear extender red light issue is because you have used a wireless connection source to connect the networking devices, i.e. the Netgear wireless range extender and the host router. To take care of the problem, you need to invest in a wired source of connection. In simple words, you need to get out of your house and purchase an Ethernet cable. Remember, in order to ensure a stable and finger-tight cable connection, you need to make use of a non-damaged Ethernet cable to connect the extender to the router. Otherwise, you will experience more technical issues.
- Avoid WiFi Interference
If the signals emitted from your Netgear wireless range extender are getting interrupted, then also you can experience the red light issue. Now, the question arises, how are the signals of the extender getting interrupted? Well, the answer to that question is very simple, i.e. bad location. In case you have placed your Netgear extender near cordless phones, washing machines, fish tanks, mirrors, microwave ovens, treadmills, televisions, and refrigerators, then the signals of your extender were bound to get interrupted. To troubleshoot the issue, you ought to change the location of your Netgear extender.
- Do Netgear Extender Firmware Update
Another thing that can be done from your side in the process of troubleshooting the Netgear extender red light issue is updating the firmware of the networking device. Doing Netgear extender firmware update will not just fix the red light issue for you but also improve its overall performance. In order to update the firmware of your extender, you need to access its default IP address. Now, you might be thinking about what the default IP address of your device is. Well, for most of the extenders, the default IP address is 192.168.1.250. To be certain about yours, it is recommended that you refer to the user manual.
- Move the WiFi Devices Closer
Considering you are reading this hack, it means that none of the aforementioned hacks were able to assist you. In that case, you should check how far your extender is placed from the host router. If it is too far, then you need to bring it close to the router or vice-versa. Maintaining a safe distance between the networking devices will ensure that the signals emitted by them are being transmitted properly throughout the house. Just make sure that while pulling the devices closer, you are not eliminating the distance between them, as in, you are not keeping them too close, or else their signals will clash.
Conclusion
These were the troubleshooting hacks through which one can get rid of the Netgear extender red light issue. Hopefully, you will be able to resolve this issue after following the hacks given in this article. On the off chance, you are still experiencing it; it is recommended that you reset your Netgear wireless range extender to its default factory settings. You can do so by following the guidelines mentioned in the user manual.
Check Also: How to Fix Netgear Nighthawk Keeps Dropping WiFi Issue?
Did you like reading this post? Was it worth your time? Whether your answer is a happy yes or a sad no, share your feedback with your fellow readers. Now, you might be wondering how to do so, right? Well, you need to make use of the comment section. Simply enter what you have to say there and press the Enter key on the keyboard.
